[Jul 24, 2023] New Updated HPE6-A72 Exam Questions 2023 [Q38-Q59]

Rate this post

[Jul 24, 2023] New Updated HPE6-A72 Exam Questions 2023

Updated Free HP HPE6-A72 Test Engine Questions with 90 Q&As

HP HPE6-A72 exam is designed to test the knowledge and skills of IT professionals in the area of Aruba switching products and solutions. Aruba is a leading provider of networking equipment and its switching products are widely used in enterprise networks. Aruba Certified Switching Associate Exam certification exam is intended for individuals who are looking to validate their understanding of Aruba switching technologies and demonstrate their ability to configure and troubleshoot Aruba switches.

Q38. Core(config)# user admin password
Core(config)# interface mgmt
Core(config-if-mgmt)# ip static 10.254.16.89/22
Core(config-if-mgmt)# default-gateway 10.254.19.129
Core(config)# ssh server vrf mgmt
Core(config)# https-server vrf mgmt
You are tasked with configuring the Core switch to be managed by NetEdit. Currently, the Core switch is at factory-default settings.
Which two steps are missing? (Choose two.)

Core(config)# https-server rest access-mode read-write

Core(config-if-mgmt)# no shutdown

Core(config-if-mgmt)# no tftp-server

Core(config-if-mgmt)# enable

Core(config)# https-server rest access-mode read-only

Q39. Which security benefit does SNMPv3 offer that SNMPv2 does not offer?

SSL encryption

Scopes

Data confidentially

RADIUS groups

Q40. Which network category applies to a SOHO internal network?

SD-WAN

LAN

WAN

Internet

Q41. What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

copy running-config checkpoint startup-config

copy startup-config running-config

copy running-config initial-checkpoint

copy running-config default

Q42. Refer to the exhibit

What is true regarding VLAN 50 according to the diagram above?

VLAN 50 is part of a switched virtual interface (SVI) that was never routed causing it to be down.

Since VLAN 50 has not been assigned to any enabled physical port, the status is down.

VLAN 50 is assigned only to Trunk ports which is why no ports are listed under interfaces.

VLAN 50 was never added to the vlan-database and therefore is in a down state.

Q43. Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.

Q44. Refer to the exhibit.

The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?

The command page

The command terminal length 30

The command more

The command less

Q45. Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.

Q46. Refer to the exhibit.

The above scenario shows a packet from the Server destined for the Firewall. Switch-A and Switch-B are bundled as VSF stack. The LAG between the VSF stack and the firewall indicates a hash function to forward the packet on port 2/1/2.
Which statement is true regarding how Switch-A will forward the packet?

Switch-A will forward the packet on port 1/1/2. VSF will override the typical LAG hash function used for the physical interface selection.

Switch-A will drop the packet. Multi-Chassis lag to multi-chassis lag is not a supported feature of VSF.

Switch-A will encapsulate the packet using GRE to forward to Switch-B in order for the packet to egress on port 2/1/2 per the hash function.

Switch-A will forward the packet along the VSF link to Switch-B so that it will egress on port 2/1/2 per the hash function.

Q47. Core# configure terminal
Core(config)# vrf Green
Core(config-vrf)# exit
Core(config)#
Core(config)# interface vlan 50
Core(config-if-vlan)# ?
Given the configuration on the CORE switch shown above, what command would follow to assign the switched virtual interface (SVI) vlan 50 to the VRF created?

Core(config-if-vlan)# vrf attach Green

Core(config-if-vlan)# ip vpn-instance Green

Core(config-if-vlan)# ip vrf forwarding Green

Core(config-if-vlan)# routing-context Green vrf

Q48. Refer to the exhibit.

What command (output shown above) gives the optics serial number and part number information?

show interface physical

show interface transceiver

show inventory

show interface optics

Q49. Which two statements are true regarding Checkpoints on Aruba switches? (Choose two.)

Rolling back to a prior checkpoint triggers a reboot of the switch.

Stacking switches using VSF or VSX will disable the Checkpoint feature.

A checkpoint is a snapshot of the running-configuration and relevant metadata at the time the checkpoint was created.

System-generated checkpoints are created after a configuration change and 5 minutes of inactivity.

Checkpoints are available on AOS 5400R switches, as well as on all AOS-CX switches.

Q50. What are two available options as part of a DHCP offer message? (Choose two.)

SSID

DNS server IP

Subnet Mask

LLDP-MED

VLANID

Q51. Match the switching term to the correct definition.

Q52. Refer to the exhibit.

The Aruba 8400 in the exhibit is member 2 of a VSX stack.
Which command will enter the interface sub configuration mode for the port, indicated by the orange square?

8400(config)# interface 2/4/15

8400(config)# interface 1/7/16

8400(config)# interface 1/4/15

8400(config)# interface 2/3/17

Q53. Refer to the exhibit.

What change on Core-1 will result in a successful ping to 10.1.1.254 from the management interface?

Use the command ping 10.1.1.254 vrf mgmt

Use the command ping 10.1.1.254/24

Change the Core-1 management address to 10.1.1.1/25 first

The destination 10.1.1.254 requires configuring a static route

Q54. What are two mechanisms supported on AOS-CX 6300 switches used in Multi-active Detection to determine the status of the Primary member? (Choose two.)

Management interface split detection

Peer switch-based detection

Loopback keepalives

ARP-based

BFD

Q55. Click on the colored box that corresponds with the line that best represents Unicast traffic flow.

Q56. You have completed a successful VSF stack between two switches.
Without manually assigning a backup switch, what is the expected output when issuing a show vsf command?