2023 Realistic Verified Free Cisco 300-615 Exam Questions [Q100-Q124]

Rate this post

2023 Realistic Verified Free Cisco 300-615 Exam Questions

300-615 Real Exam Questions and Answers FREE

Cisco 300-615 exam is an essential certification exam for professionals who want to excel in the field of networking. Troubleshooting Cisco Data Center Infrastructure certification is designed to test the candidate’s knowledge and skills in troubleshooting complex data center infrastructure issues. Troubleshooting Cisco Data Center Infrastructure certification program is recognized globally and can help individuals gain recognition as an expert in the industry.

Q100.

Refer to the exhibit. vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)

Match vPC domain ID between the two devices.

Configure IP address on the interface.

Activate VLANs on the vPC.

Configure vPC peer link and vPC peer keepalive correctly.

Configure one of the switches as primary for the vPC.

Q101. A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action prevents this issue from reoccurring?

Verify that the SFPs are supported.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.

Run the shutdown and then no shutdown commands on the interface.

Run the switchport ignore bit-errors command on the interface.

Q102. A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

Q103. Refer to the exhibit.

A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?

Enable ISSD after the downgrade is complete.

Roll back to the original image.

Reload the switch.

Shut and no shut the interfaces to the FEX.

Q104. An engineer enables the packet postcards feature on a Cisco Nexus 9000 Series Switch but receives the error message “Error: Cannot configure postcard when inband-telemetry is configured.” Which action resolves the issue?

Disable the telemetry feature

Disable the software-telemetry feature

Disable the hardware-telemetry feature

Disable the inband-telemetry feature

Q105. The external routes fail to propagate to leaf switches in Cisco ACI fabric Which two actions resolve the issue?
(Choose two.)

Enable the VTEP pool in the fabric

Assign an MP-BGP AS number to the fabric.

Specify the spine nodes as route reflectors

Associate the correct contract to the L30ut.

Configure an MP-BGP area.

Q106. Refer to the exhibit.

The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?

Reconfigure the initiator and the target to be in the same zones.

Reactivate the zoneset.

Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

Q107. Refer to the exhibit.

A recent configuration change removes the HSRP adjacency between the SW-1 and SW-2 Cisco Nexus switches. The change causes the servers on this subnet to lose Internet access. Which action restores the connectivity of all servers on VLAN 13?

Disable HSRP IP redirects on SW-1.

Set the HSRP priority to 70 on SW-1.

Activate HSRP preempt on SW-2.

Set the HSRP password on SW-2.

Q108. A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

Verify that the SFPs are supported.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.

Run the shutdown and then no shutdown command on the interface.

Run the switchport ignore bit-errors command on the interface.

Q109. A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

Q110. A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)

Load an uncorrupt bootloader image.

Load an uncorrupt kickstart image.

Reconnect L1/L2 cables between the Fis.

Reformat the fabric interconnect.

Load the correct version of the boot image.

Q111. A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

Q112. A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager Which set of steps resolves the issue?

Q113. A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

Q114.

Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network.
After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?

On MDS interface vfc 1/1, change switchport mode configuration to VF

On N9K interface vfc11, change switchport mode configuration to NP

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E

Q115. A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?

Configure the SAN boot target in the service profile.

Configure the SAN boot target to any configuration mode.

Use a predefined local disk configuration policy.

Remove the local disk configuration policy.

Q116. An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply.
Which action resolves the issues?

Create the peer names before creating the templates.

Assign the secondary template first, and then set the peer name.

Assign both templates simultaneously.

Assign the primary template first, and then set the peer name.

Q117. Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

Modify the VLAN assignment to vNICs.

Change the PIN groups on the vHBAs.

Modify the FCoE VLAN.

Set the FCoE VLAN as the native VLAN on server uplinks.

Q118. What does this adapter output indicate?
adapter 1/6/1 (fls): 2# lunlist 9
vnic: 9 lifid: 6
– FLOGI State : flogi est (fc_id Oxac0e04)
– PLOGI Sessions
– WWNN 50:0a:09:83:8d:53:43:44 WWPN 50:0a:09:83:8d:53:43:44 fc_id 0x000000
– LUN’s configured (SCSI Type, Version, Vendor, Serial No.)
– LUN ID: Ox0000000000000000 access failure
-REPORT LUNs Query Response
– Nameserver Query Response
-WWPN: 54:b1:6a:94:64:3e:73:44

The configured initiator LUN ID does not match the configured target LUN ID

The target device configuration does not allow the initiator to access the LUN

The port types between the target and initiator are incorrectly configured

The target of the configured zone does not match the target of the configured boot order

Q119.

Refer to the exhibit. An engineer is investigating a role mapping issue on a switch. The users report that they cannot view the IP addresses under the tenant “corp”. Which action resolves the issue?

Add the users to the RADIUS server.

Update the UNIX ID.

Configure the correct secret password between the APIC and the RADIUS server.

Add the updated avpair to include/corp/admin/

Q120. Drag and drop the commands from the left onto the correct categories on the right.

Q121. Refer to the exhibit.

A network engineer has connected the Nexus switch management port to the Internet using DHCP to allow the Guest shell running on the switch to download Python packages. The engineer can ping google.com successfully from the Nexus switch, but the Guest shell failed to download any Python packages. Which action resolves the problem?

Update the Python packages on the Cisco Nexus switch directly.

Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP.

Manually configure NTP in the Guest shell.

Connect Guest shell to data plane interfaces to be able to connect to the networks outside the Cisco Nexus switch.

Q122. Drag and drop the commands from the left onto the correct categories on the right.

Q123. Refer to the exhibit.

A network engineer needs to capture traffic from the VMs that utilize the IOM host interface Eth1/1/23 of a Cisco UCS B-Series chassis. A traffic analyzer is used to get traffic captured from the Eth1/4 interface of the subordinate fabric interconnect. The network engineer notices that traffic is not captured on the traffic analyzer. Which action resolves the issue?

Span the traffic from the Eth 1/2 of the subordinate fabric interconnect.

Span the traffic from the Eth 1/4 of the subordinate fabric interconnect.

Span the traffic from the Eth 1/2 of the primary fabric interconnect.

Span the traffic from the Eth 1/4 of the primary fabric interconnect.

Q124. Refer to the exhibit.

An engineer performs a POST operation using REST API on the Cisco Nexus switch to retrieve a managed object, but the operation fails. Which configuration resolves the issue?