[Oct 29, 2022] 200-301 Exam Dumps – Try Best 200-301 Exam Questions – Test4Cram [Q339-Q362]

Rate this post

[Oct 29, 2022] 200-301 Exam Dumps – Try Best 200-301 Exam Questions – Test4Cram

Verified 200-301 exam dumps Q&As with Correct 635 Questions and Answers

NEW QUESTION 339
Drag and drop the WLAN components from the left onto the correct descriptions on the right.

NEW QUESTION 340
What is the default Syslog facility level?

local 6

local 7

local 5

local 4

NEW QUESTION 341
Refer to the exhibit.

The default-information originate command is configured under the R1 OSPF configuration After testing workstations on VLAN 20 at Site B cannot reach a DNS server on the Internet Which action corrects the configuration issue?

Add the default-information originate command onR2

Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1

Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2

Add the always keyword to the default-information originate command on R1

NEW QUESTION 342
Refer to the exhibit.

IP connectivity between the three routers is configured. OSPF adjacencies must be established.
1. Configure R1 and R2 Router IDs using the interface IP addresses from the link that is shared between them.
2. Configure the R2 links with a max value facing R1 and R3. R2 must become the DR. R1 and R3 links facing R2 must remain with the default OSPF configuration for DR election. Verify the configuration after clearing the OSPF process.
3. Using a host wildcard mask, configure all three routers to advertise their respective Loopback1 networks.
4. Configure the link between R1 and R3 to disable their ability to add other OSPF routers.

Answer as below configuration:
on R1
conf terminal
interface Loopback0
ip address 10.10.1.1 255.255.255.255
!
interface Loopback1
ip address 192.168.1.1 255.255.255.0
!
interface Ethernet0/0
no shut
ip address 10.10.12.1 255.255.255.0
ip ospf 1 area 0
duplex auto
!
interface Ethernet0/1
no shut
ip address 10.10.13.1 255.255.255.0
ip ospf 1 area 0
duplex auto
!
router ospf 1
router-id 10.10.12.1
network 10.10.1.1 0.0.0.0 area 0
network 192.168.1.0 0.0.0.255 area 0
!
copy run star
—————————————
On R2
conf terminal
interface Loopback0
ip address 10.10.2.2 255.255.255.255
!
interface Loopback1
ip address 192.168.2.2 255.255.255.0
!
interface Ethernet0/0
no shut
ip address 10.10.12.2 255.255.255.0
ip ospf priority 255
ip ospf 1 area 0
duplex auto
!
interface Ethernet0/2
no shut
ip address 10.10.23.2 255.255.255.0
ip ospf priority 255
ip ospf 1 area 0
duplex auto
!
router ospf 1
network 10.10.2.2 0.0.0.0 area 0
network 192.168.2.0 0.0.0.255 area 0
!
copy runs start
———————–
On R3
conf ter
interface Loopback0
ip address 10.10.3.3 255.255.255.255
!
interface Loopback1
ip address 192.168.3.3 255.255.255.0
!
interface Ethernet0/1
no shut
ip address 10.10.13.3 255.255.255.0
ip ospf 1 area 0
duplex auto
!
interface Ethernet0/2
no shut
ip address 10.10.23.3 255.255.255.0
ip ospf 1 area 0
duplex auto
!
router ospf 1
network 10.10.3.3 0.0.0.0 area 0
network 192.168.3.0 0.0.0.255 area 0
!
copy run start
!

NEW QUESTION 343
Refer to the exhibit.

Which type of route does R1 use to reach host 10.10.13.10/32?

floating static route

host route

default route

network route

Explanation
From the output, we see R1 will use the entry “O 10.10.13.0/25 [110/4576] via 10.10.10.1, …” to reach host
10.10.13.10. This is a network route.Note: “B* 0.0.0.0/0 …” is a default route.

NEW QUESTION 344
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two.)

Enable NTP authentication.

Verify the time zone.

Specify the IP address of the NTP server.

Set the NTP server private key.

Disable NTP broadcasts.

Section: IP Services

NEW QUESTION 345
Drag drop the descriptions from the left onto the correct configuration-management technologies on the right.

Explanation

The focus of Ansible is to be streamlined and fast, and to require no node agent installation.
Thus, Ansible performs all functions over SSH. Ansible is built on Python, in contrast to the Ruby foundation of Puppet and Chef.
TCP port 10002 is the command port. It may be configured in the Chef Push Jobs configuration file .
This port allows Chef Push Jobs clients to communicate with the Chef Push Jobs server.
Puppet is an open-source configuration management solution, which is built with Ruby and offers custom Domain Specific Language (DSL) and Embedded Ruby (ERB) templates to create custom Puppet language files, offering a declarative-paradigm programming approach.
A Puppet piece of code is called a manifest, and is a file with .pp extension.

NEW QUESTION 346
Drag and drop the functions of DHCP from the left onto any of the positions on the right Not all functions are used

NEW QUESTION 347
On workstations running Microsoft Windows, which protocol provides the default gateway for the device?

DHCP

STP

SNMP

DNS

NEW QUESTION 348
Drag and drop the functions from the left onto the correct network components on the right

NEW QUESTION 349
Refer to the exhibit.

Router R1 Fa0/0 is unable ping router R3 Fa0/1.
Which action must be taken in router R1 to help resolve the configuration issue?

set the default network as 20.20.20.0/24

set the default gateway as 20.20.20.2

configure a static route with Fa0/1 as the egress interface to reach the 20.20.20.0/24 network

configure a static route with 10.10.10.2 as the next hop to reach the 20.20.20.0/24 network

NEW QUESTION 350
how to see dhcp conflict?

show ip dhcp pool

show dhcp database

show ip dhcp conflict

NEW QUESTION 351
Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.

NEW QUESTION 352
Drag and drop the AAA functions from the left onto the correct AAA services on the right

NEW QUESTION 353
Drag and drop the attack-mitigation techniques from the left onto the Types of attack that they mitigate on the right.

NEW QUESTION 354
Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

auto

active

desirable

NEW QUESTION 355
What are two roles of the Dynamic Host Configuration Protocol (DHCP)? (Choose two.)

The DHCP server assigns IP addresses without requiring the client to renew them.

The DHCP server leases client IP addresses dynamically.

The DHCP client can request up to four DNS server addresses.

The DHCP server offers the ability to exclude specific IP addresses from a pool of IP addresses.

The DHCP client maintains a pool of IP addresses it can assign.

NEW QUESTION 356
Refer to the Exhibit.

After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1.
which error must be corrected?

There is a native VLAN mismatch

Access mode is configured on the switch ports.

The PCs are m the incorrect VLAN

All VLANs are not enabled on the trunk

NEW QUESTION 357
Refer to Exhibit.

How does SW2 interact with other switches in this VTP domain?

It processes VTP updates from any VTP clients on the network on its access ports.

It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports

It forwards only the VTP advertisements that it receives on its trunk ports.

It transmits and processes VTP updates from any VTP Clients on the network on its trunk ports

Reference:
https://www.cisco.com/c/en/us/support/docs/lan-switching/vtp/10558-21.html The VTP mode of SW2 is transparent so it only forwards the VTP updates it receives to its trunk links without processing them.

NEW QUESTION 358
Refer to the exhibit.

Router R1 is running three different routing protocols. Which route characteristic is used by the router to forward the packet that it receives for destination IP 172.16.32.1?

longest prefix

metric

cost

administrative distance

NEW QUESTION 359
Refer to the exhibit.

A network engineer must block access for all computers on VLAN 20 to the web server via HTTP All other computers must be able to access the web server Which configuration when applied to switch A accomplishes this task?

Option A

Option B

Option C

Option D

NEW QUESTION 360

Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to
10.10.13.128/25 at Site A?

It sends packets out of interface Fa0/1 only.

It sends packets out of interface Fa0/2 only.

It load-balances traffic out of Fa0/1 and Fa0/2.

It cannot send packets to 10.10.13.128/25.

Section: IP Connectivity

NEW QUESTION 361
Which function dose the range of private IPv4 addresses perform?

allow multiple companies to each use the same address without conflicts

provides a direct connection for hosts from outside of the enterprise network

ensues that NAT is not required to reach the internet with private range addressing

enable secure communications to the internet for all external hosts

NEW QUESTION 362
Refer to the exhibit.

An engineer is required to verify that the network parameters are valid for the users wireless LAN connectivity on a /24 subnet. Drag and drop the values from the left onto the network parameters on the right. Not all values are used.

Loading …

Target Audience

According to Cisco, the new CCNA designation is well-suited to specific roles such as a network administrator and network support engineer. Some topics that are included in the certification exam would also suit CCNA technicians working alongside software developers in many organizations.

Topics Covered in Cisco 200-301 Exam

In a nutshell, the Cisco 200-301 exam embodies the questions covering the basics of the latest technologies and software development knowledge. The skills measured in the test tackle various topics, including but not limited to: