C_TS422_2022 Dumps Special Discount for limited time Try FOR FREE [Q20-Q41]

Rate this post

C_TS422_2022 Dumps Special Discount for limited time Try FOR FREE

C_TS422_2022 Dumps for success in Actual Exam Jan-2024]

QUESTION 20
How can you set up the supply source for the Kanban process in SAP S/4HANA?
Note: There are 3 correct answers to this question.

Use stock transfer reservations for stock transfer.

Use purchase orders for external procurement.

Use quotations for internal and external procurement

Use run schedule quantities for in-house production.

Use purchasing costs for automated source prioritization.

QUESTION 21
You have maintained the parameters for simple discontinuation in the material master of a component. Which business process will be affected if the available stock is zero and the discontinuation date is in the past?

Kanban

Material requirements planning

Backflushing

Production order release

QUESTION 22
What will happen in the MRP run if you have created a new MRP-relevant material that supports both in-house production and external procurement?

The MRP run assumes external procurement.

The MRP run assumes in-house production.

The MRP run does NOT consider the material; it has to be planned interactivelty

The MRP run plans the material only if a quotation has been maintained.

QUESTION 23
Your project uses process orders for the production of liquid chemicals. What can you define to ensure that production flow only happens in suitable and physically connected tanks? Note: There are 2 correct answers to this question.

Resource matrix

Resource network

Resource hierarchy

Resource selection

QUESTION 24
Which of the following are possible configuration steps when setting up the alert monitor in Advanced Planning? Note: There are 2 correct answers to this question.

Create an object selection variant for priority-category-related alerts.

Assign the alert profile to the overall profile.

Create an object selection variant for production-planning-related alerts.

Assign the overall profile to the authorization profile.

QUESTION 25
Which time elements are relevant for lead time scheduling of a production order? Note:
There are 2 correct answers to this question.

setup time

Opening Period

Float after Production

Total replenishment lead time

QUESTION 26
Your quality department detects a deviation in a raw material batch. Unfortunately, this batch has already been used in production. How can you identify all affected finished goods stocks?
Note: There are 2 correct answers to this question.

Use the Batch Information Cockpit.

Use batch derivation.

Use batch determination

Use the batch where-used list.

QUESTION 27
How can you characterize dependent requirements in material requirements planning?
Note: There are 2 correct answers to this question.

They are created with exact times in Advanced Planning.

They are created when an independent requirement is created for the finished product.

They are created on assembly level during the planning run.

They are only created for multilevel bill of material (BOM) structures

QUESTION 28
Which of the following processes lead to an entry in the MRP planning file?
Note: There are 3 correct answers to this question.

Changing the storage bin in warehouse management

Changing the procurement type in the product master

Changing the operation times in the production data structure

Changing the stock in inventory management

Changing the purchasing contract in materials management

QUESTION 29
How would you define pegging in the context of Advanced Planning?

An evaluation that is ordered according to the network structure of all related products and represents the coverage of issue elements with receipt elements

An evaluation that is ordered according to the bill-of-material structure of all related products and represents the relationship between the receipt and the issue elements

An evaluation to verify if there are material or capacity shortages in the ^ network after the production planning run

An evaluation to verify if there are overstock situations in the balance between receipt and issue elements after the production planning run

QUESTION 30
What could be the reason for multiple commitments, where several operations have the same scheduled dates on a work center after dispatching?
Note: There are 2 correct answers to this question.

The Finite Scheduling indicator is NOT set in the strategy profile.

The work center has several individual capacities

The Change Planning Direction indicator is set in the strategy profile

Alternative work centers are fully occupied.

QUESTION 31
Which of the following elements does MRP take into account during net requirement calculation? Note:
There are 2 correct answers to this question.

Forecast key figures

Safety Stock

Maximum stock level

Purchase orders

QUESTION 32
What data can you maintain in the subitems of a bill of material (BOM)?
Note: There are 2 correct answers to this question.

Installation point

Item type

Quantity

Scrap percentage

QUESTION 33
How can a material availability check be triggered automatically for a production order?
Note: There are 2 correct answers to this question.

By capacity planning

By mass processing

By order release

By order confirmation

QUESTION 34
What are some benefits of planning with planned independent requirements? Note: There are 2 correct answers to this question.

Reduced production times

Reduced delivery times

Option to use make-to-order production

Option to forecast planning for production resources

QUESTION 35
You use planning strategy Finite Scheduling with Reverse and want to allow scheduling the past. How can you parameterize this in the strategy profile?

Specify a negative planning horizon.

Specify a positive planning horizon.

Specify a positive offset time.

Specify a negative offset time.

QUESTION 36
Your production planners must execute planning only for specific resources. How can you achieve this in Advanced Planning (PP/DS)?

Use a propagation range.

Use a resource group

Use a planning area.

Use a planning group.

QUESTION 37
What could be the reason for different combinations of components in a multiple bill of material (BOM)?
Note: There are 2 correct answers to this question.

BOM header status

Manufacturing date

Lot size

BOM item status

QUESTION 38
For production orders, cost object controlling (COC) can be carried out on an order-related or product- related basis. Which of the following do you have to consider?
Note: There are 2 correct answers to this question.

In pro duct-related COC, all costs are debited and credited to a product cost collector.

Order-related COC is beneficial in a flexible production environment

Product-related COC is used in manufacturing for co-products

In order-related COC, individual production orders do NOT have cost segments.

QUESTION 39
In the Capacity Scheduling Table, which settings can you select for the planning strategy?
Note: There are 3 correct answers to this question.

Finiteness level

Fixed pegging

Scheduling control

Planning mode

Direction

QUESTION 40
Why would you use phantom assemblies? Note: There are 3 correct answers to this question.

To increase the number of planning levels

To simplify the structure of bills of material

To reduce the number of material masters

To make the assignment of components easier

To reduce the number of changes required in bills of material

QUESTION 41
What are the consequences when you assign a planned order to a production line manually, using the planning table in repetitive manufacturing?

The planned order is converted to a production order.

The planned order’s component availability is checked.

The planned order generates capacity requirements

The planned order’s components are copied to the picking list.