[Full-Version] 2024 New 300-510 Actual Exam Dumps, Cisco Practice Test [Q54-Q73]

Rate this post

[Full-Version] 2024 New 300-510 Actual Exam Dumps, Cisco Practice Test

Study HIGH Quality 300-510 Free Study Guides and Exams Tutorials

Q54. An engineer with an employee ID: 4535:15:507 must implement PIM-SSM in the network to support a new multicast messaging service. All the routers in the network run a distance vector routing protocol. Unicast routing is established on the network and is working normally. What must the engineer enable to continue the implementation process?

IGMPv3 on all interfaces that participate in multicast

PIM RP feature on the network

PIM dense mode on all devices on the network

PIM dense mode and IGMPv2 on all interfaces that participate in multicast

Q55. Drag and Drop Question
Drag and drop the route-manipulation methods from the left onto their features on the right.

Q56. Refer to the exhibit.

CE1 is the gateway router into the provider network via PE1. A network operator must inject a default route into OSPF area 0. All devices inside area 0 must be able to reach PE1. Which configuration achieves this goal?

Option A

Option B

Option C

Option D

Q57. Which statement about BFD on Cisco IOS XR Software is true?

Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.

Cisco IOS XR Software does not support BFD multihop for IPv4.

Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.

BFD is not compatible between Cisco IOS XR and Cisco IOS Software.

A router running BFD in Cisco IOS software can designate a router running BFD in Cisco IOS XR software as its peer using the bfd neighbor command; the Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship. https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r6-1/routing/configuration/guide/b-routing-cg-crs-61x/b-routing-cg-crs-61x_chapter_0100.html Reference:
guide/b-routing-cg-asr9000-63x/b-routing-cg-asr9000-63x_chapter_0100.html

Q58. Refer to the exhibit. While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?

Set up a priority different than 0 in the interface.

Modify the router ID to be the interface IP on the serial.

Modify the IP address or mask of the interface to a valid one.

Set the network type in S1/0 to point-to-point.

Q59. Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.

Q60. For which reason can two devices fail to establish an OSPF neighbor relationship?

The two devices have different process IDs

The two devices have different network types

The two devices have different router IDs

The two devices have the same area ID

Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html

Q61. Which two differences should be considered when deciding whether to implement to implement routing policies or route maps? (Choose two.)

Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed.

Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially.

Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program.

Route policies require sequence numbers, but route maps are implemented without sequencing.

Route maps are supported in Cisco 10S Software and routing policies are supported in Cisco IOS XR Software.

Q62. In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?

The receiver explicitly requests its desired traffic from the RP on the shared tree.

The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.

The RP on the shared tree floods traffic out of all PIM configured interfaces.

The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.

Q63. You have configured MSDP peering between two autonomous systems that pass traffic between two sites, but the peering has failed to come up.
Which task do you perform to begin troubleshooting the problem?

Verify that multicast has been disabled globally

Verify that PIM-DM is configured on the source interface

Verify that both source interfaces are reachable from both peers

Verify that the two MSDP peers allow asymmetric routing

Q64. Refer to the exhibit.

R1 is expected to receive routes originating from AS 65516 and from any ASs that are directly attached to it. However, R1 is receiving routes only from AS 65516. Which action corrects the configuration?

Change the regular expression in the AS-path permit filter to .*.

Change the regular expression in the AS-path permit filter to ^65516_[0-9]*$.

Add the regular expression ^$. in the AS-path filter to permit the traffic from R2.

Change the regular expression in the AS-path permit filter to _65516_.

Q65. Refer to the exhibit. Which attribute can router 1 alter so that only other iBGP peers prefer to use
192.168.4.2 as the next hop for route 192.168.3.0/24?

MED

local preference

origin

weight

Q66. Refer to the exhibit.

An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?

Router 1 sends and receives multiple best paths from neighbor 192.168.1.1

Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes

Router 1 sends only one best path to neighbor 192 168.1.1.

Router 1 receives only one best path from neighbor 192.168.1.1

Q67. What is the function of BGP confederations?

They require routers to use private AS numbers.

They eliminate the need for a fully-meshed internal BGP design.

They enable a single device to distribute a common configuration to its peers

They assign an external BGP router to serve as the route reflector

Q68. Refer to the exhibit.

Refer to the exhibit Reuters R2. R3, R4 and R5 all reside in the same area, with R1 in a different area R3 is overutilized and the engineer wants to reduce its CPU load The engineer configured router R4 to summarize routes that it receives from R5. but R3 is still receiving all of the R5 routes. Which action resolves the issue?

Configure R3 in a new area,

Configure R2 as a Level 1 router

Configure the summary routes on R5.

Configure R4 as a Level I-Level 2 router

Q69. Refer to the exhibit.

After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship What is the reason tor the problem?

The two routers have the same area ID.

The two routers have different iS-types

The two routers have the same network ID

The two routers cannot authenticate with one another

Q70. Refer to the exhibit.

After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?

Router 2 receives a Type 5 LSAs from router 1 for its connected subnets

Router 2 uses router 3 as the next hop for 192.168.0.0/24

Router 2 uses router 1 as the next hop for 192.168.0.0/24

Router 2 receives a Type 7 LSAs from router 3 for its connected subnets

Q71. Refer to the exhibit.

Refer to the exhibit. Company X is multihomed to a service provider. With the default settings, the link between PE2 and CE1 is the primary link, but company X has asked for the link between PE4 and CE2 to operate as the primary instead. A network engineer used a route map with local-preference to manipulate the routes from PE2 to CE1 to be less desirable and applied the route map on PE2 outbound to CE1. However, the path from PE2 to CE1 is still preferred. Which action must the engineer take so that the desired path is chosen?

Apply local-preference on PE2 outbound to CE2 with a value less than 100.

Configure the AS path prepend attribute to increase the number of hops between CE2 and PE4.

Configure the weight attribute on PE2 in the outbound direction to CE2 with a value less than 65535.

Apply MED in the outbound direction on PE2 to CE1 with a cost lower than the path from PE4 to CE2.

Q72. Refer to the exhibit.

R3 is:
failing to accept multicast RP information from Domain-A
advertising MSDP SA messages to R1 and R4
receiving SA messages only from R4
Which command must the engineer implement to resolve the issue?

R3# ip msdp sa-filter in 192.168.3.1

R3# no ip msap sa-filter in 192.168.1.1
C R3# no ip msdp peer 192.168.1.1

R3# ip msdp sa-filter out 192.168.1.1

Q73. An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network. Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)

Loading …

Cisco 300-510 certification exam is a rigorous assessment that tests the knowledge and skills of IT professionals in implementing advanced routing solutions for service providers. It is a prerequisite for obtaining the Cisco Certified Specialist – Service Provider Advanced Routing Implementation certification and is highly valued by employers in the service provider industry. Candidates who pass 300-510 exam demonstrate a high level of proficiency in implementing advanced routing solutions and are well-positioned to advance their careers in this field.

Get 100% Real Free CCNP Service Provider 300-510 Sample Questions: https://www.test4cram.com/300-510_real-exam-dumps.html

Leave a Reply Cancel reply